CAS/CS Series

CAS/CS Series
CAS/CS Series

Features

  • Sensitive type and standard type are available
  • Fully Sealed
Recognized Component Mark

File No.:E75887

RoHS Compliant

Contact Ratings

Contact Arrangement2C
Contact Resistance≤100mΩ(100mA 6VDC)
Contact MaterialSiIver AIIoy, Gold FLash
Contact Rating
(Resistive)
2A/30VDC, 2.5A/12VDC
0.5A/125VAC, 0.6A/120VAC
Minimum Load1mA/10mV(Reference Value)
Max. Switching Voltage240VAC/120VDC
Max. Switching Current2A
Max. Switching Power72VA/60W
Mechanical Life1×108 operations
Electrical LifeSee more details at “safety approval ratings”

Characteristics

Insulation Resistance1000MΩ (at 500VDC)
Dielectric
Strength
Between coil & contacts1000VAC 1min
Between open contacts1000VAC 1min
Operate time (at nomi. volt.)≤7ms
Release time (at nomi. volt.)≤5ms
Humidity98% RH
Operation temperature-40°C~+85°C
UL Class BInsulation System Class B
Shock
Resistance
Functional100m/s2
Destructive980m/s2
Vibration resistance10Hz ~ 55Hz 1.5mm DA
Unit weightApprox. 5g
ConstructionSealed Type

Notes:
1) The data shown above are initial values.
2) Please find coil temperature curve in the characteristic curves.

Ordering Information

CAS112/CS212DC12 –XXXX
Model:
CAS112=Standard type
CS212=Sensitive type
Coil VoltageCustomer Code

Coil Data at 25°C

Standard Type

Nominal
Voltage
VDC
Operate
Voltage
(Max.)
VDC
Release
Voltage
(Min.)
VDC
*Max.
Allowable
Voltage
VDC
Coil
Resistance
Ω±10%
53.750.257.045
64.500.308.466
96.750.4512.3140
129.000.6017.4280
2418.001.2034.01070
4836.002.4064.93900

Sensitive Type

Nominal
Voltage
VDC
Operate
Voltage
(Max.)
VDC
Release
Voltage
(Min.)
VDC
*Max.
Allowable
Voltage
VDC
Coil
Resistance
Ω±10%
53.750.2512.5167
64.500.3015.0240
96.750.4522.5540
129.000.6030.0960
1813.500.9040.01620
2418.001.2052.92880
4836.002.4084.97680

Note:”*Max Allowable Voltage”: The relay coil can endure max allowable voltage for a short period time only.

Coil

Coil PowerStandard Type:500mW ~ 590mW
Sensitive Type:150mW ~ 300mW

Safety Approval Ratings

UL&CULN.O./N.C.:2A 30VDC, 6×103OPS
N.O./N.C.:2.5A 12VDC, 6×103OPS
N.O./N.C.:0.5A 125VAC, G.P., 6×103OPS
N.O./N.C.:0.6A 120VAC, G.P., 6×103OPS

NOTES:
1. All values without specified temperature are at 25°C.
2. The above lists the typical loads only. Other loads may be available upon request.

OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT. Unit: inch(mm)

Outline Dimensions

CAS/CS Series Outline Dimensions

Wiring Diagram
(Bottom view)

CAS/CS Series Wiring Diagram

PCB Layout
(Bottom view)

CAS/CS Series PCB Layout

 

* The tolerance without indicating for PCB layout is always ±0.1mm.

Unless otherwise specified tolerances are:

≤1mm>1mm and ≤5mm>5mm
±0.2mm±0.3mm±0.4mm

CHARACTERISTIC CURVES

MAXIMUM SWITCHING POWER

Maximum Switching Power

LIFE CURVE

Life Curve

CONTACT RESISTANCE

Contact Resistance

PACKAGING SPECIFICATION

PAPER BOXOUTER CARTONOUTER CARTON SIZE
1000PCS4000PCSL495mm*W315mm*H245mm

APPLICATION GUIDELINES

Automatic Wave Soldering
* Wave solder is the optimum method for soldering.
* Adjust the level of solder so that it does not overflow onto the top of the PC board.
* Unless otherwise specified, solder under the following conditions depending on the type of relay.

Preheat time
20°C-100°C
Rising slope
20°C-120°C
Decreasing slope
Peak-150°C
Slodering temperature
255°C-265°C
90±5 seconds<3°C/s<4°C/s3~5s

Hand Soldering
* Keep the tip of the soldering iron clean.

Solder lron30W or 60W
lron Tip TemperatureApprox. 350°C 662°F
Solder TimeWithin approx. 3 seconds

* Immediate air cooling is recommended to prevent deterioration of the relay and surrounding parts due to soldering heat.
* Although the sealed type relay can be cleaned, avoid immersing the relay into cold liquid
(such as washing solvent) immediately after soldering. Doing so may deteriorate the sealing performance.

Discard the dropped product

PDF Document